Omega-engineering DP3300 Series Manual de usuario

Programmable Dual Channel Monitor DP3300 Series User's Manual OMEGA ENGINEERING, INC., ONE OMEGA DRIVE, STAM

DP3300 Series User’s Manual Page9 RESETTING COUNT: The COUNT shown for each channel can be reset to zero or preset for a count down (depending on cou

DP3300 Series User’s Manual Page10 the indication of the elapsed time. Maximum time indicated is 999.59.59 hours. To reset the timing and start it al

DP3300 Series User’s Manual Page11 ‘Channel ON/OFF’ Setup After displaying input type, the next step turns a channel ON or OFF. This determines whet

DP3300 Series User’s Manual Page12 suppose a flow transducer outputs a 0.130Vdc to 5.000Vdc signal which corresponds to a flow rate of 0 to 40 gal./mi

DP3300 Series User’s Manual Page13 When this parameter is set for "Normally Closed", the relay is closed when readings are below LIMIT, and

DP3300 Series User’s Manual Page14 Display Options On pushing SETUP key while the display is flashing SYS , the display briefly shows 'dSP OPt&

DP3300 Series User’s Manual Page15 1. Connect a thermocouple calibration source to the unit. 2. Dial in 1100 degrees centigrade on the calibrator (N

DP3300 Series User’s Manual Page16 SET UP Voltage or Current Setup Thermocouple / RTD / Thermister Setup Select Channel Turn Ch On/Off Select Input T

DP3300 Series User’s Manual Page17 SET UP Select System or Channel Programming For System Programing Refer to Flow Chart for Analog Input SELECT INPUT

DP3300 Series User’s Manual Page18 SETUP FOR A PULSE CHANNEL: Turning a Channel ON or OFF The very first thing after selecting a channel is to turn

DP3300 Series User’s Manual Page1 SPECIFICATIONS:...

DP3300 Series User’s Manual Page19 FUNCTION DISPLAY SHOWS TO CHANGE active digit flashing. active digit. Division Fac

DP3300 Series User’s Manual Page20 FUNCTION DISPLAY SHOWS TO CHANGE Latching or non - 'LATCH' for latching mode. Push ^v key to o

DP3300 Series User’s Manual Page21 If the unit is setup as an RPM monitor then following steps are performed for setting up various parameters: FUNCTI

DP3300 Series User’s Manual Page22 NOTE: Process value for respective relay must be below limit value for it to reset. Other wise the key sequence wi

DP3300 Series User’s Manual Page23 FIG. 3: Power, Input/Output connections & rear view of the instrument. INPUT/OUTPUT CONN

DP3300 Series User’s Manual Page24 MOUNTING 3.70” (94mm) 4.05 ” (10 2.87 mm) 1.77” (45mm) 0.15” dia. (3.81mm) Figure 4. Panel Cutout Di

DP3300 Series User’s Manual Page25 WARRANTY/DISCLAIMER

DP3300 Series User’s Manual Page26

DP3300 Series User’s Manual Page27

DP3300 Series User’s Manual Page2 Turning a Channel ON or OFF ...

DP3300 Series User’s Manual Page3 SPECIFICATIONS: (Typical @ 25C and rated supply voltage unless otherwise specified) STANDARD INPUTS • * 4-20ma

DP3300 Series User’s Manual Page4 DESCRIPTION: A highly versatile series, DP3300 offers a unique combination of two analog channels or two pulse in

DP3300 Series User’s Manual Page5 Table 1. How to Display Parameters PEAKS: A very useful function on the system is tracking the highest (peak) a

DP3300 Series User’s Manual Page6 RESETTING PEAKS Peaks can be reset to current process value e.g. if channel 1 is reading 200 C, its peaks can be

DP3300 Series User’s Manual Page7 below the limit (minus the relay) deadband. The second mode is manual reset. Once the limits are energized, they wil

DP3300 Series User’s Manual Page8 MODES OF OPERATION FOR COUNTER: COUNT UP CONFIGURATION: MODE 0: (Count up with manual reset to zero) In this mod